Why Is My Dental Imaging Software Failing To Access Images On The NAS After A Windows Update?
Summary
This guide helps you troubleshoot and resolve: Why Is My Dental Imaging Software Failing To Access Images On The NAS After A Windows Update?. Follow the steps below to fix the issue.
Common Causes
This article helps Brisbane and Gold Coast dental clinics troubleshoot why dental imaging software cannot access radiographic images stored on a local Synology or QNAP NAS after a Windows security patch or feature update. Because appointment downtime directly impacts patient scheduling and revenue, the steps below are ordered to isolate the fault quickly between the local surgery PC, the local network, and the NAS itself.
Quick Fix Steps
- Restart the surgery PC and attempt to open a patient chart in the dental imaging software.
- Open File Explorer and enter the NAS IP address in the address bar (for example,
\\192.168.1.50) to verify basic network reachability. - Open a web browser on the same PC and log in to Synology DSM or QNAP QTS to confirm the NAS is online and the storage volume is healthy.
- Test image access from a second workstation in the surgery to determine if the issue is isolated to one PC.
Detailed Instructions
1. Local PC Diagnosis
- Open Command Prompt as Administrator and run
ipconfig /flushdnsto clear stale DNS entries that may have changed after the Windows update. - Ping the NAS by IP address using
ping 192.168.1.50(replace with your NAS IP). If the ping fails, the issue is likely network-related rather than software-related. - Run
nslookup [nas-hostname]to confirm the NAS hostname resolves to the correct IP address. - Open Credential Manager from the Start menu, select Windows Credentials, and check for any stored entries for the NAS IP or hostname. Remove outdated entries and re-enter the NAS username and password if prompted.
- In File Explorer, navigate to This PC and select Map network drive. Choose a drive letter, enter the NAS share path (for example,
\\NAS-NAME\DentalImages), and select Reconnect at sign-in. If the connection fails, note the exact error message. - Check the Windows network profile. Open Settings, go to Network & Internet, select Properties for the active connection, and ensure the profile is set to Private. A Public profile restricts File and Printer Sharing and can block SMB access after a Windows update.
- Verify the dental imaging software service is running. Right-click the Start button, select Task Manager, go to the Services tab, and confirm the imaging software service status is Running. Restart the service if necessary.
- Check the dental imaging software settings. Open the application settings or preferences, navigate to the storage or image archive location, and confirm it is pointing to the correct mapped drive or UNC path (for example,
\\NAS-NAME\DentalImages). Update the path if the Windows update reset application settings.
2. Check SMB Protocol Negotiation
Windows updates may disable legacy SMB1 support for security reasons. Many older NAS devices still rely on SMB1, which can cause a “network path not found” or “trusted host unavailable” error in dental imaging software.
- Open Control Panel and select Programs.
- Click Turn Windows features on or off.
- Scroll to SMB 1.0/CIFS File Sharing Support and confirm whether it is enabled or disabled.
- If your NAS only supports SMB1, contact your IT provider to update the NAS firmware and share settings to use SMB2 or SMB3. Do not enable SMB1 on the Windows PC as it is a deprecated and insecure protocol.
- If the NAS supports SMB2 or SMB3, leave SMB1 disabled and ensure the NAS is configured to use the modern protocol.
PowerShell alternative: Open PowerShell as Administrator and run Get-SmbServerConfiguration | Select-Object EnableSMB1Protocol to check SMB1 status. To disable SMB1, run Set-SmbServerConfiguration -EnableSMB1Protocol $false.
3. Windows Firewall and File Sharing
- Open Control Panel, go to System and Security, and select Windows Defender Firewall.
- Click Allow an app or feature through Windows Defender Firewall.
- Ensure File and Printer Sharing is checked for both Private and Public network profiles.
- Confirm the network profile is set to Private. Public profiles restrict file sharing and may have been applied automatically after the Windows update.
- If the firewall was recently reset by a Windows update, select Restore defaults and re-add the dental imaging software executable to the allowed apps list.
PowerShell alternative: Open PowerShell as Administrator and run Get-NetFirewallRule -DisplayName "File and Printer Sharing (SMB-In)" to verify the rule is enabled.
4. Check NAS Event Logs
- Open a web browser on any device on the same network and log in to Synology DSM or QNAP QTS using the NAS IP address.
- Navigate to Log Center (Synology DSM) or System Logs (QNAP QTS).
- Filter logs by SMB, Network, or Storage to identify connection failures, permission denials, or service errors recorded around the time of the Windows update.
- Note any error codes or timestamps to provide to your support team when opening a ticket.
5. Network Verification
- Confirm the surgery PC and NAS are connected to the same switch or VLAN. Treatment rooms and server rooms are sometimes segmented, which can block SMB traffic after a network change.
- Check the switch port status for the NAS and the affected PC. Look for port errors, duplex mismatches, or a link-down state.
- If your organisation uses VLANs, verify that inter-VLAN routing allows traffic on TCP ports 445 (SMB) and 139 (NetBIOS) between the treatment room VLAN and the server room VLAN.
- Temporarily connect the affected PC directly to the same switch as the NAS using a known-good Ethernet cable to rule out cabling or wall-port faults.
6. Cloud and NAS Confirmation
- Open a web browser on any device on the same network and log in to Synology DSM or QNAP QTS using the NAS IP address.
- Navigate to Storage Manager or Storage & Snapshots and confirm the volume containing patient images is online and not degraded.
- Go to Shared Folder settings and verify the imaging software share still exists and has the correct user permissions for the surgery PC account.
- Check NAS SMB service settings to ensure SMB2 or SMB3 is enabled and SMB1 is disabled for security.
- Log in to a second workstation in the surgery and attempt to open the same patient chart. If images load successfully, the fault is isolated to the original PC.
Troubleshooting
Error: “Network path not found”
- Confirm the NAS IP address has not changed after a DHCP lease renewal. Reserve a static IP for the NAS in your router or DHCP server.
- Verify the share name is spelled correctly and is still exported on the NAS.
- Ensure SMB protocol versions match between Windows and the NAS.
Error: “Trusted host unavailable”
- Clear Windows Credential Manager entries for the NAS and re-authenticate.
- Check that the PC’s date and time are synchronised with the NAS; large time differences can break authentication.
- Confirm the NAS account used by the imaging software has not been locked or disabled.
Images load on one PC but not another
- Compare network adapter settings between the working and non-working PCs.
- Reinstall or repair the dental imaging software on the affected workstation.
- Check for third-party antivirus or endpoint security software blocking SMB access after the Windows update.
Information to Gather Before Opening a Ticket
To minimise downtime, collect the following details before contacting support:
- The exact error code and full error message displayed by the dental imaging software.
- Screenshots of the error and the File Explorer connection attempt to the NAS.
- The NAS model (for example, Synology DS220+ or QNAP TS-253D) and firmware version.
- The Windows build version (run
winverin Command Prompt). - The affected PC name and the surgery location.
- Whether the issue affects one workstation or multiple workstations.
If you have completed these steps and patient images remain inaccessible, Open a Ticket so our Brisbane and Gold Coast support team can investigate further.
Still Having Issues?
đź’» Open a Ticket