Home › Knowledgebase › KB-1661

Fujitsu Fi-Series Scanner Paper Jamming After Cleaning Rollers

Summary

This guide helps you troubleshoot and resolve: Fujitsu Fi-Series Scanner Paper Jamming After Cleaning Rollers. Follow the steps below to fix the issue.

Quick Tip: Need immediate assistance? 💻 Open a Ticket

Common Causes

Fujitsu Fi-Series scanners are commonly used by legal practices across Brisbane and the Gold Coast to digitise client files, contracts, and evidence bundles for Securex and other legal practice management systems. If your scanner reports a paper jam immediately after cleaning or replacing rollers, the issue is usually caused by improper roller seating, misalignment, or residual debris in the feed path. This guide provides model-specific steps to resolve post-cleaning jams on Fujitsu Fi-Series devices.

Always power off the scanner and disconnect the power cable before touching internal rollers or the feed path. Failure to do so may result in injury or equipment damage.

Identify Your Fi-Series Model and Roller Part Number

Before cleaning or replacing rollers, confirm your exact Fujitsu Fi-Series model number. The model label is typically located on the rear or base of the scanner chassis. Using incorrect rollers can cause persistent jam errors and premature wear on the feed mechanism.

  1. Locate the model label on your scanner and note the full model number (for example, fi-7160, fi-7180, or fi-7600).
  2. Cross-reference the model number with the Fujitsu consumables guide to identify the correct roller kit part number.
  3. Only use genuine Fujitsu rollers. Third-party rollers may not meet manufacturer tolerances and can trigger false paper jam errors.
  4. If you have already installed replacement rollers, verify that the part number matches your specific Fi-Series model before proceeding.

Cleaning Rollers Properly

Rollers should be cleaned when they show signs of dust buildup, paper residue, or toner transfer. Improper cleaning can leave residue that causes the scanner to report a jam even when no paper is present.

  1. Power off the scanner and disconnect the power cable.
  2. Open the ADF (Automatic Document Feeder) cover according to your Fi-Series model instructions.
  3. Remove the rollers if your model allows user-serviceable roller removal.
  4. Use a lint-free cloth lightly dampened with water or an approved Fujitsu roller cleaner. Do not use alcohol, solvents, or abrasive cleaners.
  5. Gently wipe the roller surface to remove dust and paper residue. Rotate the roller manually to clean the full circumference.
  6. Allow the rollers to dry completely before reinstallation.
  7. Reinstall the rollers, ensuring they are seated flush and locked into place.
  8. Close the ADF cover, reconnect the power cable, and power on the scanner.

Roller Alignment and Reseating

After cleaning or replacing rollers, incorrect alignment is the most common cause of immediate paper jam errors. Fi-Series rollers must sit correctly in their mounts with alignment marks properly oriented.

  1. Open the ADF cover and inspect each roller mount.
  2. Confirm that the roller alignment marks or seating indicators match the positions shown in your Fi-Series model user guide.
  3. Press each roller firmly until it clicks or locks into position. A loose roller can shift during feeding and trigger a sensor error.
  4. Check that the separation pad is correctly seated and shows no signs of excessive wear.
  5. Adjust the ADF paper guides so they sit snugly against the paper stack without applying excessive pressure.
  6. Close the cover and load a small stack of clean, staple-free paper.
  7. Run a test scan of a single page to confirm the jam error has cleared.

Cleaning Scanner Sensors

False paper jam errors often occur when dust or debris obstructs the scanner sensors. Sensor cleaning should be performed alongside roller maintenance.

  1. Power off the scanner and disconnect the power cable.
  2. Open the ADF cover and locate the feed path sensors. Refer to your Fi-Series model documentation for sensor locations.
  3. Use a dry, lint-free cloth or a compressed air duster to gently remove dust from the sensor area.
  4. Do not touch the sensor elements with fingers or sharp objects.
  5. Close the cover, reconnect power, and turn the scanner on.
  6. Perform a test scan to verify that the false jam error no longer appears.

Resetting the Jam Counter or Clearing Error Memory

After replacing rollers, some Fujitsu Fi-Series scanners retain a jam counter or error memory that can continue to display a paper jam message even after the mechanical issue is resolved.

  1. Power on the scanner and wait for the ready status on the LCD panel.
  2. Press the Menu button on the scanner control panel.
  3. Use the arrow keys to navigate to Maintenance or Counter, depending on your Fi-Series model.
  4. Select Jam Counter or Error History.
  5. Choose Reset or Clear and confirm the selection when prompted.
  6. Exit the menu and power cycle the scanner.
  7. Run a test scan to confirm the error memory has been cleared.

Driver and PC Connectivity Checks

If the mechanical feed path is clear but the scanner continues to report a jam, a driver-level communication error between the scanner and PC may be causing the scanner to misreport status.

  1. On your Windows PC, select Start, type Device Manager, and press Enter.
  2. Expand Imaging devices and locate your Fujitsu scanner.
  3. If a yellow warning icon appears, right-click the scanner and select Update driver.
  4. Choose Search automatically for drivers and follow the prompts.
  5. Alternatively, download the latest ISIS or TWAIN driver for your specific Fi-Series model from the Fujitsu support website.
  6. Restart your PC after installing driver updates.
  7. Open your scanning application and perform a test scan to confirm communication is restored.

Troubleshooting Persistent Jam Errors

Scanner Still Reports Paper Jam After Cleaning

False Jam Errors During Multi-Page Scanning

Scan Completes but Jam Error Appears Afterwards

Still Having Issues?

Need more help? If the issue persists after trying these steps, please open a support ticket and our team will assist you.

💻 Open a Ticket